On 2022/3/25 5:57, Mike Kravetz wrote:
On 3/24/22 00:40, Peng Liu wrote:

Hugepages can be specified to pernode since "hugetlbfs: extend
the definition of hugepages parameter to support node allocation",
but the following two problems are observed.

1) Confusing behavior is observed when both 1G and 2M hugepage
is set after "numa=off".
 cmdline hugepage settings:
  hugepagesz=1G hugepages=0:3,1:3
  hugepagesz=2M hugepages=0:1024,1:1024
 results:
  HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
  HugeTLB registered 2.00 MiB page size, pre-allocated 1024 pages

2) Using invalid option values causes the entire kernel boot option
string to be reported as Unknown.
 Unknown kernel command line parameters "hugepages=0:1024,1:1024"

Thank you for debugging and sending the patch!

My first thought was "If someone is specifying 'numa=off' as well as
numa node specific allocations on the same command line, we should just
fail the allocation request".  However, this same situation could exist
without the 'numa=off' option as long as an invalid node is included in
the list.
We will "specifying 'numa=off' as well as numa node specific allocations"
for some debugging and test cases. If the original command line can be
partly effective, this will be convenient. Yet, we also test "an invalid
node is included in the list", the behavior is the same with "numa=off".

With your patch, the node specific allocations are parsed (and processed)
until there is an error.  So, in the example above 3 1G pages and 1024 2M
pages are allocated on node 0.  That seems correct.

Now suppose the node specific allocations are specified as:
hugepagesz=1G hugepages=1:3,0:3
hugepagesz=2M hugepages=1:1024,0:1024
For this case, with/without this patch, huge page will be not allocated
on any node.
Since node 1 is invalid, we experience an error here and do not allocate
any pages on node 0.

I am wondering if we should just error and ignore the entire string if
ANY of the specified nodes are invalid?  Thoughts?

Thank you for your response.

This patch only to be consistent between 2M/1G behavior, and repair "return 0"
as 1d02b444b8d1 ("tracing: Fix return value of __setup handlers").
With this patch, a node could allocate huge pages until there is an error, and it
will print the invalid parameter from the first parse error. So, I think this
is acceptable.

The following tests is added with this patch.

Case1:
settings:
hugepagesz=1G hugepages=0:3,1:3,2:3
hugepagesz=2M hugepages=0:1024,1:1024,3:1024

results:
HugeTLB: Invalid hugepages parameter 1:3,2:3
HugeTLB: Invalid hugepages parameter 1:1024,3:1024
HugeTLB registered 1.00 GiB page size, pre-allocated 3 pages
HugeTLB registered 2.00 MiB page size, pre-allocated 1024 pages

Case2:

settings:
hugepagesz=1G hugepages=1:3,0:3
hugepagesz=2M hugepages=1:1024,0:1024

results:
HugeTLB: Invalid hugepages parameter 1:3,0:3
HugeTLB: Invalid hugepages parameter 1:1024,0:1024
HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages

Peng Liu.