[PATCH v10 11/18] arm64: kexec: arm64_relocate_new_kernel clean-ups and optimizations

[Pavel Tatashin <pasha.tatashin@soleen.com>]

In preparation to bigger changes to arm64_relocate_new_kernel that would
enable this function to do MMU backed memory copy, do few clean-ups and
optimizations. These include:

1. Call raw_dcache_line_size()  only when relocation is actually going to
   happen. i.e. kdump type kexec, does not need it.

2.  copy_page(dest, src, tmps...) increments dest and src by PAGE_SIZE, so
    no need to store dest prior to calling copy_page and increment it
    after. Also, src is not used after a copy, not need to copy either.

3. For consistency use comment on the same line with instruction when it
   describes the instruction itself.

4. Some comment corrections

Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
---
 arch/arm64/kernel/relocate_kernel.S | 36 +++++++----------------------
 1 file changed, 8 insertions(+), 28 deletions(-)

diff --git a/arch/arm64/kernel/relocate_kernel.S b/arch/arm64/kernel/relocate_kernel.S
index 84eec95ec06c..462ffbc37071 100644
--- a/arch/arm64/kernel/relocate_kernel.S
+++ b/arch/arm64/kernel/relocate_kernel.S
@@ -17,28 +17,24 @@
 /*
  * arm64_relocate_new_kernel - Put a 2nd stage image in place and boot it.
  *
- * The memory that the old kernel occupies may be overwritten when coping the
+ * The memory that the old kernel occupies may be overwritten when copying the
  * new image to its final location.  To assure that the
  * arm64_relocate_new_kernel routine which does that copy is not overwritten,
  * all code and data needed by arm64_relocate_new_kernel must be between the
  * symbols arm64_relocate_new_kernel and arm64_relocate_new_kernel_end.  The
  * machine_kexec() routine will copy arm64_relocate_new_kernel to the kexec
- * control_code_page, a special page which has been set up to be preserved
- * during the copy operation.
+ * safe memory that has been set up to be preserved during the copy operation.
  */
 SYM_CODE_START(arm64_relocate_new_kernel)
-
 	/* Setup the list loop variables. */
 	mov	x18, x2				/* x18 = dtb address */
 	mov	x17, x1				/* x17 = kimage_start */
 	mov	x16, x0				/* x16 = kimage_head */
-	raw_dcache_line_size x15, x0		/* x15 = dcache line size */
 	mov	x14, xzr			/* x14 = entry ptr */
 	mov	x13, xzr			/* x13 = copy dest */
-
 	/* Check if the new image needs relocation. */
 	tbnz	x16, IND_DONE_BIT, .Ldone
-
+	raw_dcache_line_size x15, x0		/* x15 = dcache line size */
 .Lloop:
 	and	x12, x16, PAGE_MASK		/* x12 = addr */
 
@@ -57,34 +53,18 @@ SYM_CODE_START(arm64_relocate_new_kernel)
 	b.lo    2b
 	dsb     sy
 
-	mov x20, x13
-	mov x21, x12
-	copy_page x20, x21, x0, x1, x2, x3, x4, x5, x6, x7
-
-	/* dest += PAGE_SIZE */
-	add	x13, x13, PAGE_SIZE
+	copy_page x13, x12, x0, x1, x2, x3, x4, x5, x6, x7
 	b	.Lnext
-
 .Ltest_indirection:
 	tbz	x16, IND_INDIRECTION_BIT, .Ltest_destination
-
-	/* ptr = addr */
-	mov	x14, x12
+	mov	x14, x12			/* ptr = addr */
 	b	.Lnext
-
 .Ltest_destination:
 	tbz	x16, IND_DESTINATION_BIT, .Lnext
-
-	/* dest = addr */
-	mov	x13, x12
-
+	mov	x13, x12			/* dest = addr */
 .Lnext:
-	/* entry = *ptr++ */
-	ldr	x16, [x14], #8
-
-	/* while (!(entry & DONE)) */
-	tbz	x16, IND_DONE_BIT, .Lloop
-
+	ldr	x16, [x14], #8			/* entry = *ptr++ */
+	tbz	x16, IND_DONE_BIT, .Lloop	/* while (!(entry & DONE)) */
 .Ldone:
 	/* wait for writes from copy_page to finish */
 	dsb	nsh
-- 
2.25.1