linux-mm.kvack.org archive mirror
 help / color / mirror / Atom feed
From: Andrew Morton <akpm@linux-foundation.org>
To: Rik van Riel <riel@redhat.com>
Cc: linux-kernel@vger.kernel.org, linux-mm@kvack.org,
	safari-kernel@safari.iki.fi
Subject: Re: [PATCH] prevent kswapd from freeing excessive amounts of lowmem
Date: Wed, 5 Sep 2007 18:23:05 -0700	[thread overview]
Message-ID: <20070905182305.e5d08acf.akpm@linux-foundation.org> (raw)
In-Reply-To: <46DF3545.4050604@redhat.com>

> On Wed, 05 Sep 2007 19:01:25 -0400 Rik van Riel <riel@redhat.com> wrote:
> The current VM can get itself into trouble fairly easily on systems
> with a small ZONE_HIGHMEM, which is common on i686 computers with
> 1GB of memory.
> 
> On one side, page_alloc() will allocate down to zone->pages_low,
> while on the other side, kswapd() and balance_pgdat() will try
> to free memory from every zone, until every zone has more free
> pages than zone->pages_high.
> 
> Highmem can be filled up to zone->pages_low with page tables,
> ramfs, vmalloc allocations and other unswappable things quite
> easily and without many bad side effects, since we still have
> a huge ZONE_NORMAL to do future allocations from.
>
> However, as long as the number of free pages in the highmem
> zone is below zone->pages_high, kswapd will continue swapping
> things out from ZONE_NORMAL, too!

crap.  I guess suitably-fashioned mlock could do the same thing.

> Sami Farin managed to get his system into a stage where kswapd
> had freed about 700MB of low memory and was still "going strong".
> 
> The attached patch will make kswapd stop paging out data from
> zones when there is more than enough memory free.

hm.  Did highmem's all_unreclaimable get set?  If so perhaps we could use
that in some way.

>  We do go above
> zone->pages_high in order to keep pressure between zones equal
> in normal circumstances, but the patch should prevent the kind
> of excesses that made Sami's computer totally unusable.
> 
> Please merge this into -mm.
> 
> Signed-off-by: Rik van Riel <riel@redhat.com>
> 
> 
> [linux-2.6-excessive-pageout.patch  text/x-patch (715B)]
> --- linux-2.6.22.noarch/mm/vmscan.c.excessive	2007-09-05 12:19:49.000000000 -0400
> +++ linux-2.6.22.noarch/mm/vmscan.c	2007-09-05 12:21:40.000000000 -0400
> @@ -1371,7 +1371,13 @@ loop_again:
>  			temp_priority[i] = priority;
>  			sc.nr_scanned = 0;
>  			note_zone_scanning_priority(zone, priority);
> -			nr_reclaimed += shrink_zone(priority, zone, &sc);
> +			/*
> +			 * We put equal pressure on every zone, unless one
> +			 * zone has way too many pages free already.
> +			 */
> +			if (!zone_watermark_ok(zone, order, 8*zone->pages_high,
> +						end_zone, 0))
> +				nr_reclaimed += shrink_zone(priority, zone, &sc);
>  			reclaim_state->reclaimed_slab = 0;
>  			nr_slab = shrink_slab(sc.nr_scanned, GFP_KERNEL,
>  						lru_pages);

I guess for a very small upper zone and a very large lower zone this could
still put the scan balancing out of whack, fixable by a smarter version of
"8*zone->pages_high" but it doesn't seem very likely that this will affect
things much.

Why doesn't direct reclaim need similar treatment?

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>

  reply	other threads:[~2007-09-06  1:23 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-09-05 23:01 Rik van Riel
2007-09-06  1:23 ` Andrew Morton [this message]
2007-09-06 16:38   ` Rik van Riel
2007-09-06 22:34     ` Andrew Morton
2007-09-06 22:47       ` Rik van Riel
2007-09-07 12:24 ` Pavel Machek
2007-09-08 20:20   ` Rik van Riel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20070905182305.e5d08acf.akpm@linux-foundation.org \
    --to=akpm@linux-foundation.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mm@kvack.org \
    --cc=riel@redhat.com \
    --cc=safari-kernel@safari.iki.fi \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox